Whether the water-based film adhesive meets the quality requirements of composite products, in addition to the quality of the glue itself, but also related to the paper, film, equipment accuracy, operating experience and other supporting factors in the film coating process, after long-term practice, we summarized the common problems in the application of water-based film adhesive, and put forward the production reasons and solutions, to help the film coating personnel quickly find a solution. Common Problem Cause Solution Combination fastness is not good The membrane surface tension is not enough Test the fitting surface ≥39 Dynes with Dyne pen before use Excessive ink thickness Lengthen the time after fitting The amount of glue is too small Increase the amount of glue appropriately Compound pressure is too small Increase pressure appropriately Radial fringe Using glue is too thick - causing stringing The glue itself thickens and changes the glue After the empty machine runs for a long time, the rubber tank thickens with new glue Compound pressure is too small Increase pressure appropriately Uneven or radial scratch on the surface of the roller - uneven thickness of the glue Smooth the top roller or replace it with a roller The film itself is curled and uneven - resulting in uneven gluing Flatten or replace the film with a new one Composite diagonal stripes The tension between the left and right sides is inconsistent when the film is removed Adjust tension until removed The pressure at both ends of the film is inconsistent The tension at both ends is inconsistent during winding The top roller has a taper - resulting in a different amount of glue, resulting in a variation in friction The lack of equality of each guide roller leads to oblique wrinkles The laminating board is uneven Too much winding tension - film strain Tone down The linear speed of the press roll is different from that of the cardboard transfer Fix a machine Wire plate uneven - deformed after moisture absorption Dry and recombine Excessive machine jitter Finishing machine Roller pressure is too low Increase roll The cardboard is husked along the radial edge Cardboard deformed by moisture - flounces Let dry before recombining Too little glue Increase glue Excessive machine jitter Reinforce the machine The edge of the roller overflow rubber dust in time to remove - edge Degumming

In the actual operation of our manufacturer, whether the laminating products can normally complete the factory and meet the requirements of customers, in addition to the quality of the laminating glue itself, it is also related to the supporting factors such as paper, film, equipment accuracy, environment, and operating experience in the composite process. Often in some small details, it will cause unnecessary mistakes, which delays the time and increases the cost, which can be described as losing the wife and folding the army. Next, we will teach you a few tips to save costs. 1.The storage of glue is very important, should be placed in a suitable place according to the product instructions for storage, sunscreen and antifreeze, avoid direct sunlight and other requirements, the remaining glue after use should also be sealed and stored to prevent crust and mold, shorten the shelf life, resulting in unnecessary waste. 2.After the printing ink of the product to be printed, it must be dry and coated with film adhesive. 3.The coating roller of the laminating machine must be cleaned before use to ensure that no other impurities are attached to it. 4.Different coated adhesives should not be mixed and used at the same time to prevent adverse chemical reactions and losses. 5.If there is dust on the surface of the print, in principle, it should be wiped clean in the coating, if the dust is small, you can choose the special adhesive for the coating powder.

With the progress of science and technology, the printing technology industry is also developing rapidly, and more and more adhesives are used in the packaging and printing industry, and more and more varieties are also available. The film coating process is widely used in a variety of packaging, small to medicine boxes, crafts boxes, large to outer boxes and various product packaging. Some coating methods are pre-coated (hot melt type), and some are dry composite (solvent-based). In the late 1990s, with the strengthening of people's awareness of environmental protection, the domestic phase developed a more suitable wet composite technology (water-soluble adhesive), and there were water-based laminating and water-based laminating adhesives that matched each other. Pre-coating process This is a widely used film coating process, in the BOPP film coated with a layer of hot melt adhesive, after cooling into a film, the printing manufacturer in the film directly precoated film heating, in the hot melt adhesive melting state, at the same time through the pressure to make it fit on the print. The process and equipment are relatively simple, no environmental pollution, the product also has excellent brightness, but due to the high manufacturing cost of pre-coating film, large power consumption, the coating speed is slow. Wet laminating process This is a new laminating process developed in recent years, generally using water-based laminating glue coated on BOPP film, without drying, directly with printed matter cold press, roll. Because it does not need drying, the power consumption is only 10% of the coating, about 1.5KW/h, and the coating speed can be doubled, which can greatly improve the work efficiency and reduce the cost. Environmentally friendly water-based laminating adhesive makes the laminating industry completely rid of the toxic, flammable, polluted and other defects brought by the traditional process. And the laminating products have better brightness and clarity, so in just a few years, the traditional laminating process has been gradually eliminated. Sinograce Chemical SA2291 Water based Bopp and paper lamination adhesive.This product is a self-crosslinking emulsion with the advantages of small amount of glue, high peel strength, good toughness, no glue opening when exposed to moisture, deep embossing and shallow embossing, and general use on flat surfaces.

Lovers who like to collect books know that books are exposed to the air and vulnerable to damage because they are placed in the bookcase for a long time, and the edge of the book is produced in this environment. Book edge hot printing technology can not only effectively protect books, but also play a beautification, decorative books, the original purpose of brush gold is to avoid dust falling into the book, and then avoid damage and acidification of the inside pages. Now, the top of the book, the bottom of the book, will be hot printing, but also do a lot of beautiful patterns, colors and so on. Although this hot stamping process is complicated and complex, ordinary hot stamping silver printing is widely used in daily life, as small as badges, buttons, trademarks, plastic handles, etc., to the surface decoration of furniture, has an important role and status in the printing industry. Anhui Sinograce Chemical Co., Ltd. water-based coated adhesive, is a water-based acrylic adhesive. Excellent overall performance, reasonable speed of conjunctiva after coating, fast drying of composite, good stiffness and fastness, high reflective rate, loyal to the primary color, colorless phase elegant; Coated adhesive powder ability is strong, the dry material is easy to clean, the composite product is resistant to rolling line, smashing and embossing, and has good adaptability to hot stamping, gold printing and silver printing. Wide temperature range, good freeze-thaw stability, can continue to use after freezing and thawing; High cost performance, simple process, easy to operate.