Categories
new blog
Formulation design system for waterborne coatings - film forming AIDS The polymer constituting the emulsion or dispersion generally has a glass transition temperature higher than room temperature. In order for the emulsion particles to be well fused into a uniform paint film, it is necessary to reduce the minimum film formation temperature (MFFT) of the crystallization aid.Film forming agents are ...
Water - based coating formulation design system - matting agent Matting agents are additives used to control the gloss of waterborne wood coatings to meet the broad needs of mainstream matt paints in today's market.The extinction mechanism of the matting agent can be arranged in an orderly manner on the surface of the coating film, so that the surface of the coating film is uneven, causing the lig...
Waterborne paint formulation design system - pH regulator Waterborne wood coatings may also need to adjust the pH when necessary.Most emulsions or aqueous dispersions have been adjusted to a pH of 8 to 9 when they are produced, eliminating the need for pH adjusters when making paint.If the pH value is different, add 0.05% to 0.1% of the pH adjuster during the paint making process, and adjust the p...
In the solid paint, white paint is taken as an example. The amount of titanium dioxide should be sufficient to ensure that the paint film has sufficient capping power. The amount of titanium dioxide should not be lower than 13%, but it is not necessary to be higher than 22%. The situation is the same as solvent-based white paint. Fillers may be added or not added. However, a small amount of filler...
Adhesion type and adhesion property of paint film on substrate The adhesion of the paint film to the substrate is divided into two types: mechanical adhesion and chemical attachment.Mechanical adhesion depends on the properties of the coated sheet (roughness, porosity) and the strength of the formed film; chemical adhesion refers to the mutual attraction of the paint film molecules and the plate m...
Sinograce Chemical - Jingangtai rafting trip On August 17th, Sinograce Chemical Marketing Center carried out the second quarter group building activities of the Rapids Warriors, blue sky and white clouds, green mountains and green waters, riding a rubber boat, leaping in the cool water, Sometimes light as a swallow, Now and then it gallops like a tiger, the event The thrills not only make the...
Adding certain kinds and dosages of substrate wetting agent and adhesion promoter to the transparent base formulation helps to improve the adhesion of the paint film; the type and quality of the color paste are not only related to the phase of the color paste and the transparent base. Capacity also has a certain influence on the adhesion of the paint film. The thickness of the paint film, the dryi...
The third step in the treatment of water-based paint coated substrates is sealing. The role of the water-based putty is to make the surface of the substrate such as wood not very regular and smooth and minor defects and defects, such as pores, fine cracks, pits, joints and concrete, to reduce the surface roughness and increase the flatness.The requirements for water-based putty are good adhesion a...
Spraying construction paint film than brush paint film more flat. Spray with water-based wood paint should be added on the basis of the original paint 5% ~ 30% of the tap water dilute after use, for the viscosity of the paint water should also increase, the diluted paint after its coating a 4 cup viscosity should be around 18 ~ 20s. Dilute mix well should be static at least 20 minutes, until the b...
Current problems with waterborne polyurethane adhesives: (1) Low solid content: At present, the solid content of water-based polyurethane (WPU) can reach 45%. Fewer systems lead to higher drying and transportation costs. Increasing the solid content leads to an increase in the viscosity of the system, which makes emulsification and dispersion difficult. Reduced emulsion stability. (2) Slow drying ...
Precautions for using two-component polyurethane adhesives 1.Before applying the adhesive, the surface of the adherend must be clean, dry and free of grease. 2.The resin and curing agent should be mixed in the required ratio. 3.When scraping the glue, please try to scrape it carefully as it has a defoaming effect. 4.Store adhesive in (> 10, <50 * C) and dry place 5.Run out of the mixed glue ...
Polyurethane and general epoxy products application The use of the two products requires strengthened compressive tensile cement floors or floors and drainage ditches that are resistant to corrosion by strong acids and alkalis, such as chemicals, metallurgical plants, electroplating plants, power plants, pharmaceutical plants, PCB circuit board plants, paper mills, Hardware factory, printing and d...
The choice of solvent In the printing ink manufacturing process, in consideration of the overall solvent system of the ink volatility, to improve the printing ink solvent release and reduce the solvent organic solvent residue, the use of solvents are often several volatile mixed solvents.In the printing ink manufacturing process, the main organic solvents are toluene, butanone, cyclohexanone, ethy...
Anhui Sinograce Chemical Co., Ltd Polyurethane condoms, known as condoms, are made of polyurethane condoms, similar to latex condoms. Polyurethane was applied to condom production in Japan, until the emergence of China's Nakagawa 001, which broke Japan's monopoly on the production field. Because the common latex condoms on the market are thicker and polyurethane has good ...
Composition of water bases adhesive 1.adhesive: also known as adhesive agent, after the surface treatment of two or more adhesive materials firmly connected together, and has a certain mechanical strength of chemical properties, such as epoxy resin phosphate copper oxide white latex. 2.Solid material (base material): determines the main physical, chemical and mechanical properties of rubber joints...
1.Principles of adhesive selection Consider the type, nature and hardness of the bonding material Consider the shape, structure and process conditions of the bonding material Consider the load and form (tensile force, shear force, peel force, etc.) borne by the bonding part; consider the special requirements of materials such as high temperature and low temperature resistance. 2.Properties of bond...
sinograce chemical
Sinograce Chemical is professional technical enterprise providing solutions of surface materials and manufacturing of raw materials. Sinograce Chemical Company is composed of R&D center, Manufacture center, Quality control department, Market center and International trade department. We have been dedicating to research on excellent paint/coating, adhesive for over 15 years. And now still conti...
Room 1013, Building A5, Financial Port Center, Yangzijiang Road, Baohe District, Hefei City， Anhui province, China
+86 0551 63459511
Copyright © 2015-2025 Anhui Sinograce Chemical Co., Ltd..All Rights Reserved.powered by dyyseo.com
top
English
français
русский
español
العربية