Categories
new blog
Printing mucilage requirements The requirements of printing mucilage for manual plate printing Manual table printing is to press the screen on the fabric of the table for manual scraping, and the pressure extrusion on the scraper will print the glue through the mesh hole of the pattern part to the fabric. The shear stress of the binder is small, so thePrinting mucilageis required to have good...
Waterborne polyurethane is often used in the preparation of waterborne coatings because of its excellent film formation and adhesion, excellent flexibility and wear resistance.However, water-based polyurethane dispersion contains a lot of surfactant, easy to produce bubbles, and because of the special properties of water-based polyurethane, it is necessary to use the characteristics of water-based...
The appearance of non-stick pan provides conditions for healthy cooking with less oil, and also makes cooking utensils more convenient to clean. However, in the non-stick frying pan into life at the same time, the safety of its coating has never been questioned.There are two main coating processes for non-stick frying pans: one is the traditional coating process, Teflon coating (PTFE); The second ...
Self-adhesive refers to paper, film or other special materials as fabric, coated with adhesive on the back, a composite material printed with silicon protective paper as the base paper, the reason for the rapid rise of self-adhesive in recent years, because it is very practical, and very convenient, the cost is not high, the following to tell you about a few small knowledge of self-adhesive printi...
With the continuous enhancement of human environmental awareness, environmental protection laws and regulations are also being introduced and improved. All industries are working together in the direction of environmental protection, green, healthy.With the development of flexible packaging industry, it has become an inevitable trend to reduce and remove the organic solvents used in the compound.W...
1.Excellent adhesion The polymer structure of water-based acrylic emulsion contributes to the flow and wettability of molecular chains on the substrate surface, making the coating and substrate molecules in close contact, to achieve high adhesion. 2.High load-bearing capacity of the makeup filler can significantly reduce the cost Waterborne acrylic emulsion has excellent fillability, the total sol...
"Non-stick pan" is a very common pot in the kitchen, because in the process of using less oil consumption, less smoke, but also not easy to paste the problem, so it is welcomed by many people. In recent years, however, there have been more and more controversies about non-stick pans: Some people think that non-stick coating will produce toxic substances, can not be used for a long time; Some peopl...
①BOPP / VMCPP The composite structure is mainly used in the field of light food packaging such as instant noodles, egg yolk pie and snow cake. The composite structure is most suitable for one-component aqueous adhesives. Compared with solvent-based polyurethane adhesive, single component water glue less ink transfer phenomenon, and the initial adhesion is high, without aging, can be directly cut b...
With the development of the market economy, the demand for flexible packaging in various industries is also rising year by year. The development of flexible packaging materials and processing technology continue to improve, flexible packaging in many areas is playing an increasingly important role, so what are the composite ways of flexible packaging? This article briefly describes five composite ...
The foam problem in water treatment has troubled many people, debuting the initial foam, surfactant foam, impact foam, peroxide foam, circulating water treatment with non-oxidizing fungicide generated foam, etc., so the use of defoamer in water treatment is more common, this article comprehensively introduces the principle, classification, selection and dosage of defoamer! Methods of foam eliminat...
Advantages and disadvantages of the same type of defoamer Organic defoamer such as mineral oils, amides, low alcohols, fatty acids, fatty acid esters and phosphate esters has been studied and applied earlier, belonging to the first generation of defoamer, which has the advantages of easy access to raw materials, high environmental performance and low production cost.The disadvantages are low defoa...
Defoamer is a substance with low surface tension and high surface activity, which can inhibit and eliminate foam in the liquid, that is to say, defoamer can reduce the surface tension of water, solution, suspension, etc., to prevent foam generation or eliminate the original foam.Long-term defoaming is also known as defoaming, and the length of the defoaming time is the main sign of the quality of ...
1. The effect of membrane material There are dust adsorption, particle impurities, poor plasticization and other crystal points in the film. The moisture absorption on the film surface of the material and the precipitation of additives in the material will cause composite bubbles. The thickness of the film should be as uniform as possible, if the distribution is uneven, it is easy to cause the imb...
Brand :Sinograce Type: Water base adhesive Appearance：Milky white emulsion with blue light Performance and use:This product is suitable for the coating of BOPP film, PET film and printed color paper (dry coating process). High bonding q degree, large tension compound drying speed, good parallel flow; For gold and silver cardboard, single powder paper bonding q degree, tension q, to avoid the...
As an important material for printing, ink is composed of resin, pigment, filler and auxiliary. Due to many industries such as books, packaging, construction, and circuit boards, with the gradual increase in social demand, the use of ink is also increasing. However, in the production and use of ink, due to the addition of surfactants, equipment stirring operation and environmental changes will cau...
"If there are small bubbles in the complex, opaque and foggy, it will not only affect the appearance quality, but also affect the peeling strength of the complex, reducing it, which is a very bad phenomenon." 1.The surface tension of the base film is too small, the infiltration is poor, the glue is not uniform, and the space without glue is empty and bubbles are generated. The solution is to use a...
sinograce chemical
Sinograce Chemical is professional technical enterprise providing solutions of surface materials and manufacturing of raw materials. Sinograce Chemical Company is composed of R&D center, Manufacture center, Quality control department, Market center and International trade department. We have been dedicating to research on excellent paint/coating, adhesive for over 15 years. And now still conti...
Room 1013, Building A5, Financial Port Center, Yangzijiang Road, Baohe District, Hefei City， Anhui province, China
+86 0551 63459511
Copyright © 2015-2025 Anhui Sinograce Chemical Co., Ltd..All Rights Reserved.powered by dyyseo.com
top
English
français
русский
español
العربية