Categories
new blog
Teflon coating is one of the commonly used protective coatings in metal thermal spraying processing technology services, with good non-stick, wear resistance, corrosion resistance, high temperature resistance and other characteristics, can be applied to carbon steel, stainless steel, aluminum, copper, magnesium and various alloys and other metal materials. It can also be applied to non-metall...
1.Ink The three primary color inks have different degrees of color bias, which will affect the color bias of the whole picture to different degrees. However, a small amount of color bias can be corrected from the ink preparation. When printing to grasp the gray balance of the ink used, the same amount of yellow, product, green do not produce neutral gray, they produce lighter, more turbidity with ...
Insufficient or uneven amount of glue due to insufficient amount of glue produced by the white spot can be observed in the composite machine. In the dry composite process, the coated adhesive must be able to fill the bumps and bumps on the surface of the ink and film to avoid appearance defects such as obvious white spots. When the water-based adhesive dry composite is used to produce lightweight ...
The hardness and softness of the water-based acrylic resin can be adjusted according to specific needs, but it is usually biased towards the harder side. First, the characteristics and application of water-based acrylic resin Water-based acrylic resin is an environmentally friendly water-based resin, with non-toxic, easy to clean, dry fast and other characteristics, widely used in furniture, packa...
The final state of waterborne polyurethane is a solid film. During the process from emulsion to solid film, accompanied by the evaporation of water and the concentration of water dispersion, the latex particles are close to each other. Before the solid content reaches 74%, the dispersion particles can move in the continuous phase of water. Under the influence of water/air interfacial tension, the ...
Due to the hydrophobic properties of waterborne polyurethane resin, it is difficult to dissolve in water or disperse uniformly, and the high reactivity of isocyanate groups to water, the direct synthesis of waterborne polyurethane faces many challenges. Therefore, to achieve the preparation of waterborne polyurethane, the primary strategy is to cleverly integrate hydrophilic functional groups (suc...
①The residual ink is converted into gray black ink According to the principle of color science, the complementary color of the ink mixed together, its hue will become gray black (red + green, yellow + blue-purple). Therefore, we can use this principle to deploy the complementary ink into gray-black ink by deploying the special color ink, and add it to the black ink in a certain proportion to use i...
Paper aluminum-plastic composite film in the actual application of medical packaging powder, granule packaging products compared to the plastic aluminum-plastic packaging commonly used in the market now has the following advantages: (1)The mechanical strength of the paper is high, the rigidity is good, and the ability to maintain the bag after forming is strong, which improves the cleanliness of t...
Pigment is the main component of ink, is a fine powder-like solid colored substance, can show ball, flake and other irregular shape. Generally, the diameter of pigment particles is in the range of several hundred nanometers to tens of microns (10-7~10-5m). The pigment can be evenly dispersed in the medium, but it is insoluble in the medium and does not react with the medium. Pigment is a colored b...
1.Touch optimization: the pursuit of softness and fullness In view of the frequent skin-to-skin contact of fabrics, the primary goal of the design of waterborne polyurethane coatings is to achieve soft touch and full form. This requires us to carefully balance the ratio of hard and soft segments in the formulation adjustment, while carefully selecting the types of both to ensure that the coating r...
Most coatings are composed of a base material (one or more resin mixtures), pigments (including physical pigments and functional pigments), solvents and some small amounts of additives and other coating raw materials. In the production of coatings, after the selection of various coating raw materials necessary for coating components, the next is how to make reasonable use of the technical and econ...
Aluminum foil can also be printed with water-based ink. As a non-absorbent substrate, aluminum foil poses a major challenge to water-based ink printing. However, some aluminum foil products that require food-grade printing cannot be printed with oil-based inks, so water-based inks have become the best choice. However, due to the poor absorption of aluminum foil to water-based ink, many inexperienc...
In the process of UV flexographic printing, the viscosity of the ink is one of the key factors that affect the printing quality and effect. Choosing the right viscosity UV flexographic ink is crucial to ensure printing quality and efficiency. When adjusting viscosity, it is usually necessary to consider many factors such as printing equipment, printing materials, image details and the expected pri...
First, water-based lotion Aqueous emulsion is a colloidal dispersion system with water as the continuous phase and oil or other non-aqueous substances as the dispersing phase. It is a stable dispersion system formed by tiny oil droplets coated with surfactants. Water-based emulsion has many significant advantages, such as its low viscosity, easy to brush, easy to clean, non-toxic and harmless. The...
There are several main reasons for water-based emulsion breaking: 1.Large temperature changes, water-based emulsion is easy to separate into water phase and oil phase at high temperature, and easy to crystallize at low temperature. 2.The selection of emulsifier is improper, and the type and dosage of emulsifier are different, which has a great impact on the stability of emulsification. The choice ...
The role of wax emulsion in various coatings, in the coating formulation, polyethylene wax emulsion can effectively improve the wear resistance of the paint film, the paint film is very smooth, effectively reduce the friction coefficient of the coating, play a non-adhesive role, but also improve the service life of the product. 1.Synthetic wax emulsion can improve the toughness of the coating: whe...
sinograce chemical
Sinograce Chemical is professional technical enterprise providing solutions of surface materials and manufacturing of raw materials. Sinograce Chemical Company is composed of R&D center, Manufacture center, Quality control department, Market center and International trade department. We have been dedicating to research on excellent paint/coating, adhesive for over 15 years. And now still conti...
Room 1013, Building A5, Financial Port Center, Yangzijiang Road, Baohe District, Hefei City， Anhui province, China
+86 0551 63459511
Copyright © 2015-2025 Anhui Sinograce Chemical Co., Ltd..All Rights Reserved.powered by dyyseo.com
top
English
français
русский
español
العربية