Categories
The OPP,PET film substrate | is an environmentally friendly coating using advanced material technology, which can significantly enhance the adhesion of EVA on difficult PET substrates and improve the product quality of PE card film. Card film, also known as plastic film, is a plastic film product coated with adhesive and OPP and PET as the substrate, which is widely used in the storage and protect...
Enhance the adhesion of UV ink and UV varnish on paper products! The tape won't come off Fast drying speed to meet the needs of production line Good affinity with UV varnish and UV ink Excellent strength and toughness Water-based UV base oil for high adhesion paper products Anhui Sinograce Chemical waterborne UV primer for high adhesion paper products is a high-performance waterborne coa...
Rubber mold, silicone mold, shoe mold, latex pillow mattress mold, anti-stick easy mold Teflon spray, good model flon coating, non-stick mold surface treatment process The role of mold coating Molds are common tools in the manufacturing industry and are used to make a variety of products. In order to capture the service life and production efficiency of the mold, people often coat the surface of t...
The most important difference between non-stick cookware and ordinary cookware is that the surface is coated with a layer of non-stick paint, and the Teflon non-stick cookware commonly used on the market is to coat the main raw material of fluorinated resin such as polytetrafluoroethylene coating on the metal surface such as aluminum, copper or iron, and through sintering. Properties of NI-PTFE co...
First: the treatment of the substrate First, the substrate (aluminum, stainless steel or other metal substrate) is baked at high temperature (360℃×30 minutes ~380℃×10 minutes) to carbonize the grease or degreaser cleaning for the first step of degreasing. Step 2: Roughening the surface Available corundum sand 80#~120#, pressure 0.4~0.6mpa, sandblasting, so that the surface roughness of the substra...
In the face of different needs of different industries, rollers also need to do the corresponding coating treatment, so as to improve or compensate the relevant performance of the roller. So what are the surface coating technologies for rollers? 01 Coating treatment The coating treatment of the drum includes zinc plating, chromium plating, nickel plating, etc. The different coating treatment can i...
In the use of pesticides, only a few cases are the direct use of the original drug, and most of the cases are mixed with other additives and solvents to improve its use value and reduce the cost of use. Surfactant is a kind of additives that can give greater play to the value of pesticides and reduce the cost of pesticides. It plays the role of emulsification, foaming/defoaming, dispersi...
Teflon coating is one of the commonly used protective coatings in metal thermal spraying processing technology services, with good non-stick, wear resistance, corrosion resistance, high temperature resistance and other characteristics, can be applied to carbon steel, stainless steel, aluminum, copper, magnesium and various alloys and other metal materials. It can also be applied to non-metall...
1.Ink The three primary color inks have different degrees of color bias, which will affect the color bias of the whole picture to different degrees. However, a small amount of color bias can be corrected from the ink preparation. When printing to grasp the gray balance of the ink used, the same amount of yellow, product, green do not produce neutral gray, they produce lighter, more turbidity with ...
Insufficient or uneven amount of glue due to insufficient amount of glue produced by the white spot can be observed in the composite machine. In the dry composite process, the coated adhesive must be able to fill the bumps and bumps on the surface of the ink and film to avoid appearance defects such as obvious white spots. When the water-based adhesive dry composite is used to produce lightweight ...
The hardness and softness of the water-based acrylic resin can be adjusted according to specific needs, but it is usually biased towards the harder side. First, the characteristics and application of water-based acrylic resin Water-based acrylic resin is an environmentally friendly water-based resin, with non-toxic, easy to clean, dry fast and other characteristics, widely used in furniture, packa...
The final state of waterborne polyurethane is a solid film. During the process from emulsion to solid film, accompanied by the evaporation of water and the concentration of water dispersion, the latex particles are close to each other. Before the solid content reaches 74%, the dispersion particles can move in the continuous phase of water. Under the influence of water/air interfacial tension, the ...
Due to the hydrophobic properties of waterborne polyurethane resin, it is difficult to dissolve in water or disperse uniformly, and the high reactivity of isocyanate groups to water, the direct synthesis of waterborne polyurethane faces many challenges. Therefore, to achieve the preparation of waterborne polyurethane, the primary strategy is to cleverly integrate hydrophilic functional groups (suc...
①The residual ink is converted into gray black ink According to the principle of color science, the complementary color of the ink mixed together, its hue will become gray black (red + green, yellow + blue-purple). Therefore, we can use this principle to deploy the complementary ink into gray-black ink by deploying the special color ink, and add it to the black ink in a certain proportion to use i...
Paper aluminum-plastic composite film in the actual application of medical packaging powder, granule packaging products compared to the plastic aluminum-plastic packaging commonly used in the market now has the following advantages: (1)The mechanical strength of the paper is high, the rigidity is good, and the ability to maintain the bag after forming is strong, which improves the cleanliness of t...
1.Touch optimization: the pursuit of softness and fullness In view of the frequent skin-to-skin contact of fabrics, the primary goal of the design of waterborne polyurethane coatings is to achieve soft touch and full form. This requires us to carefully balance the ratio of hard and soft segments in the formulation adjustment, while carefully selecting the types of both to ensure that the coating r...
Copyright © 2015-2024 Anhui Sinograce Chemical Co., Ltd..All Rights Reserved.powered by dyyseo.com
top