Categories
new blog
Formulation design system for waterborne coatings - film forming AIDS The polymer constituting the emulsion or dispersion generally has a glass transition temperature higher than room temperature. In order for the emulsion particles to be well fused into a uniform paint film, it is necessary to reduce the minimum film formation temperature (MFFT) of the crystallization aid.Film forming agents are ...
Plastics are classified into two types: thermosetting and thermoplastic.Among them, thermosetting plastics have high cross-linking density, good solvent resistance and heat resistance, relatively high surface polarity, and wide range of coatings available.For example, unsaturated polyester is called polyester fiberglass. The texture is hard and polar, and there are many coatings that can be used. ...
As the saying goes, three-point paint, seven-point painting. For water-based coatings, especially for water-based wood coating in the home improvement market, the level of coating technology has a direct impact on product use. In order to let everyone better master the water-based paint technology, we specially launched the water-based paint coating process series this week. The substrate treatmen...
Paint of water-based paint - Waterborne wood paint application process 2 Before using the soft brush, thoroughly soak it in clean water, remove excess water, and do not drip. The enamel paint should only reach half the length of the bristles.Brush as fast as possible, gently and smoothly brush the wood grain, and do not apply it back and forth repeatedly. Because the water-based paint dries quickl...
1.The tool Before using the soft brush, thoroughly soak it in clean water, remove excess water, and do not drip. The enamel paint should only reach half the length of the bristles.Brush as fast as possible, gently and smoothly brush the wood grain, do not apply it back and forth repeatedly, because the water-based paint is fast drying and the opening time is short, so it should be completed as soo...
Waterborne paint testing and standards:hardness Hardness is one of the most important physical properties of a coating. Coating hardness reflects the coating's ability to resist constant dents, scratches, scribes, and penetrations caused by a hard object. Testing the hardness of materials with different methods will give different results because the testing methods are for different amounts of ma...
Current problems with waterborne polyurethane adhesives: (1) Low solid content: At present, the solid content of water-based polyurethane (WPU) can reach 45%. Fewer systems lead to higher drying and transportation costs. Increasing the solid content leads to an increase in the viscosity of the system, which makes emulsification and dispersion difficult. Reduced emulsion stability. (2) Slow drying ...
Precautions for using two-component polyurethane adhesives 1.Before applying the adhesive, the surface of the adherend must be clean, dry and free of grease. 2.The resin and curing agent should be mixed in the required ratio. 3.When scraping the glue, please try to scrape it carefully as it has a defoaming effect. 4.Store adhesive in (> 10, <50 * C) and dry place 5.Run out of the mixed glue ...
Material property (pu for short) is divided into: Pouring polyurethane elastomer (CPU for short) is one of the most widely used polyurethane elastomers with the largest yield. Thermoplastic polyurethane elastomer (TPU) -- thermoplastic polyurethane elastomer accounts for about 25% of the total amount of polyurethane.Mixed polyurethane elastomer (MPU) - accounts for about 10% of the total amount of...
1.Paper-based coating resins have been switched from natural water-based resins such as celluloses to synthetic resin emulsions such as carboxystyrene butadiene emulsions, polyvinyl acetate emulsions, and acrylic emulsions, among which acrylic emulsions have more excellent properties.However, the above resins are still difficult to meet the higher requirements for the development of coated paper. ...
Composition of water bases adhesive 1.adhesive: also known as adhesive agent, after the surface treatment of two or more adhesive materials firmly connected together, and has a certain mechanical strength of chemical properties, such as epoxy resin phosphate copper oxide white latex. 2.Solid material (base material): determines the main physical, chemical and mechanical properties of rubber joints...
1.Principles of adhesive selection Consider the type, nature and hardness of the bonding material Consider the shape, structure and process conditions of the bonding material Consider the load and form (tensile force, shear force, peel force, etc.) borne by the bonding part; consider the special requirements of materials such as high temperature and low temperature resistance. 2.Properties of bond...
Automotive interior adhesive is a anionic waterborne polyurethane emulsion developed and produced by ourselves, which belongs to environmental protection waterborne polyurethane adhesive. Appearance Dark grey liquid Solid content(% ) 50±1 PH 6-9 softening point(℃) 45-55℃ Proportion（g/cm3） 1.06±0.02 viscosity（mPa.s） 1000-2000（Viscosity can be adjusted） Application Area Automobile interior adhesive ...
Laminated oil magnetic cards, Identification Card and other cards used in water-based adhesive. The card is both a document and a form or carrier of the document's existence, although it has entered the 5G era,Many things exist in electronic form, such as electronic balance cards, electronic driver's licenses, electronic health care cards, etc.But the physical card such as id card bank card is als...
Solvent selection In the printing ink manufacturing process, considering the overall solvent system of the volatile ladder, improve the printing ink solvent release and reduce printing solvent organic solvent residue, the solvent used is often a mixture of several volatile solvents. In the printing ink manufacturing process, the main organic solvents are toluene butyl ketone cyclohexanone ethyl ac...
Food packaging is divided into ordinary packaging and high-performance packaging, the corresponding waterborne polyurethane adhesive can be divided into four categories: general use, steaming boiling, transparent cooking, aluminum foil cooking.Usually such adhesives are two-component solvent-based polyurethane adhesives, the main agent is polyether or polyester polyol After the aromatic isocyanate...
sinograce chemical
Sinograce Chemical is professional technical enterprise providing solutions of surface materials and manufacturing of raw materials. Sinograce Chemical Company is composed of R&D center, Manufacture center, Quality control department, Market center and International trade department. We have been dedicating to research on excellent paint/coating, adhesive for over 15 years. And now still conti...
Room 1013, Building A5, Financial Port Center, Yangzijiang Road, Baohe District, Hefei City， Anhui province, China
+86 0551 63459511
Copyright © 2015-2025 Anhui Sinograce Chemical Co., Ltd..All Rights Reserved.powered by dyyseo.com
top
English
français
русский
español
العربية