Categories
new blog
One,Overview Paper-plastic composite can make the surface of paper printed matter more bright, smooth and color more bright and full of three-dimensional sense, but also play a role in moisture, anti-fouling, anti-counterfeiting, folding resistance, wear resistance and so on.It has been widely used and rapidly developed in printing and packaging industry at home and abroad. The market demand for p...
The amount of glue applied is insufficient or uneven Insufficient or uneven amount of glue due to insufficient amount of glue produced by the white spot can be observed in the composite machine. In the dry composite process, the coated adhesive must be able to fill the bumps and bumps on the surface of the ink and film to avoid appearance defects such as obvious white spots.When the water-based ad...
With the rapid development of printing and packaging industry, the appearance design of products is becoming more and more high-end. The composite technology used in modern exquisite printing mainly includes: paper printing and plastic film composite and plastic printing and plastic film composite, that is, paper-plastic composite and plastic-plastic composite.As a new type of packaging material, ...
Composite film manufacturer there are bubbles and spots in the composite film, what is the cause? There are many factors in this kind of situation, and the actual situation needs to be analyzed in detail. The basic elements commonly used to produce bubbles and spots are: 1, environmental factors such as dust and suspended matter interference, which requires a good environmental health area environ...
In daily life, we will use glue in many places, and we often see the figure of water-based glue. If you say you can't remember where you used glue, look at street posters, advertisements, and alley shoe repairmen.We usually use glue in class or work to stick some paper, bills and so on. It can be said that water-based glue has always been around us. In addition, water-based adhesives have also bee...
According to the different raw materials and equipment, the coating process can be divided into two kinds of coating process and pre-coating process. That is to say, the film used in the coating process is now coated, and the adhesive used is generally solvent-based and emulsion type, prepared according to need. However, the film used in the pre-coating process is pre-coated, and the adhesive used...
1. The effect of membrane material There are dust adsorption, particle impurities, poor plasticization and other crystal points in the film. The moisture absorption on the film surface of the material and the precipitation of additives in the material will cause composite bubbles. The thickness of the film should be as uniform as possible, if the distribution is uneven, it is easy to cause the imb...
Brand :Sinograce Type: Water base adhesive Appearance：Milky white emulsion with blue light Performance and use:This product is suitable for the coating of BOPP film, PET film and printed color paper (dry coating process). High bonding q degree, large tension compound drying speed, good parallel flow; For gold and silver cardboard, single powder paper bonding q degree, tension q, to avoid the...
In the production process of water-based polyurethane to add a certain type of additives, it is necessary to pay attention to its role in the various stages of storage, construction, application, and consider and evaluate its role and impact in the next section. For example, when the water-based polyurethane paint is operated with wetting and dispersing agents, it plays a certain role in storage a...
The transparency of composite film is very high, but in the composite processing of plastic film, the composite film often has problems such as insufficient transparency. So, what is the reason for affecting the transparency of the composite film? This article analyzes one by one for reference. Improper selection of adhesives: Such as the color of the adhesive itself is dark or the fluid...
"If there are small bubbles in the complex, opaque and foggy, it will not only affect the appearance quality, but also affect the peeling strength of the complex, reducing it, which is a very bad phenomenon." 1.The surface tension of the base film is too small, the infiltration is poor, the glue is not uniform, and the space without glue is empty and bubbles are generated. The solution is to use a...
Different processing methods will cause different fault manifestations, the following we mainly analyze the causes of paper thermit sealing delamination phenomenon under the gravure and solvent-free composite processing methods. The YBB paper aluminum-plastic composite film standard does not specify the composite strength index of the paper aluminum layer in the paper aluminum-plastic composite fi...
The high adhesion base coating improves the adhesion of the inkjet coating on PP paper Prevent ink from penetrating into PP composite paper substrate Fast drying speed to meet the needs of production line Good weather resistance, no yellowing Easy to use, safe and environmentally friendly Anhui sinograce company's PP composite paper digital inkjet coating adhesive base | Inkblot coating base ...
The difference between nitrile rubber and nitrile latex Different raw materials Carboxyl nitrile latex: butadiene, acrylonitrile and methacrylic acid Carboxyl nitrile butadiene latex (XNBRL) is a terpolymer of butadiene, acrylonitrile and acrylic acid or methacrylic acid, and is a modified variety of nitrile butadiene latex. Due to the introduction of carboxyl group, while containin...
This product uses butadiene, Acrylonitrile as the main raw materials, through emulsion polymerization of anionic polymer dispersion, can be used to produce disposable medical examination gloves, with excellent elongation and tensile strength The product is an environmentally friendly product, free of formaldehyde, APEO, NPEO and other harmful substances, and has excellent elongation, tensile stren...
Pressure-sensitive adhesive Pressure-sensitive adhesive is a kind of viscoelastic body that simultaneously possesses the viscous properties of liquids and the elastic properties of solids. Bonding can be achieved immediately by using finger touch pressure The purpose is to ensure a smooth surface of any adherend, so it is called Pressure-Sensitive Adhesive (PSA). The subdivision of pressure-sensit...
sinograce chemical
Sinograce Chemical is professional technical enterprise providing solutions of surface materials and manufacturing of raw materials. Sinograce Chemical Company is composed of R&D center, Manufacture center, Quality control department, Market center and International trade department. We have been dedicating to research on excellent paint/coating, adhesive for over 15 years. And now still conti...
Room 1013, Building A5, Financial Port Center, Yangzijiang Road, Baohe District, Hefei City， Anhui province, China
+86 0551 63459511
Copyright © 2015-2025 Anhui Sinograce Chemical Co., Ltd..All Rights Reserved.powered by dyyseo.com
top
English
français
русский
español
العربية