Categories
new blog
Formulation design system for waterborne coatings - film forming AIDS The polymer constituting the emulsion or dispersion generally has a glass transition temperature higher than room temperature. In order for the emulsion particles to be well fused into a uniform paint film, it is necessary to reduce the minimum film formation temperature (MFFT) of the crystallization aid.Film form...
Formulation design system for waterborne coatings - film forming AIDS The polymer constituting the emulsion or dispersion generally has a glass transition temperature higher than room temperature. In order for the emulsion particles to be well fused into a uniform paint film, it is necessary to reduce the minimum film formation temperature (MFFT) of the crystallization aid.Film forming agents are ...
The film-forming aids for waterborne wood coatings are generally alcohol ether type solvents. The most commonly used filming aids such as diethanol ethers, propylene glycol ethers and N-methylpyrrolidone have high and low boiling points.Water-based wood coatings in the summer construction, the water volatilization is faster, that is, the surface is relatively fast, some of the moisture may be encl...
From the viewpoints of molecular structure, molecular polarity and molecular interaction force, the adhesion of the paint film results from the polar group orientation of the polymer molecules in the coating, and its polar group with the polar molecules on the surface of the coated object. The mutual attraction between each other.Only when the polar phase of the two is adapted to obtain a good adh...
Cohesion and thermal expansion coefficient of paint film The force caused by the cohesion of molecules of the same substance is called cohesion.The more cohesive the coating, the worse the adhesion.In the drying process of paint, with the increase of solvent volatilization and crosslinking degree, the cohesion between film forming material molecules increases, the film produces shrinkage phenomeno...
Water - based acrylic emulsion formulation needs to be considered: water - based acrylic resin composition The choice of emulsion raw materials is the most important decision for engineers when formulating aqueous paint formulations.The main properties of the coating are determined by the resin.A wide variety of water-based acrylate emulsions, including polystyrene-acrylate emulsions, are on the m...
What parameters of resin determine coating gloss? Question: What parameters of the resin determine the gloss of the film? Some people say that it is solid content, some people say it is OH value. So, what is the most important determinant of gloss? Answer: There are many parameters that determine the gloss of the paint film. The saturation of the resin: that is, its monomer structure, this index d...
Waterborne paint testing and standards:hardness Hardness is one of the most important physical properties of a coating. Coating hardness reflects the coating's ability to resist constant dents, scratches, scribes, and penetrations caused by a hard object. Testing the hardness of materials with different methods will give different results because the testing methods are for different amounts of ma...
Water based polyurethane resin refers to a binary colloidal system in which a polyurethane resin is dissolved or dispersed in water.Water-based polyurethane resin has the advantages of easy to use, stable performance, strong adhesion, excellent gloss, good heat resistance, etc. It can be suitable for various printing methods, especially suitable for screen printing, plastic packaging and composite...
Development trend of waterborne polyurethane: Nowadays, with the stricter requirements of environmental protection policies, the environmental protection requirements for the performance of adhesives will become higher and higher. Therefore, the greening and environmental protection of composite materials will be more and more important. There will be even more urgency.Therefore, the points mentio...
Precautions for using two-component polyurethane adhesives 1.Before applying the adhesive, the surface of the adherend must be clean, dry and free of grease. 2.The resin and curing agent should be mixed in the required ratio. 3.When scraping the glue, please try to scrape it carefully as it has a defoaming effect. 4.Store adhesive in (> 10, <50 * C) and dry place 5.Run out of the mixed glue ...
Polyurethane and general epoxy products application The use of the two products requires strengthened compressive tensile cement floors or floors and drainage ditches that are resistant to corrosion by strong acids and alkalis, such as chemicals, metallurgical plants, electroplating plants, power plants, pharmaceutical plants, PCB circuit board plants, paper mills, Hardware factory, printing and d...
Glass fiber is an important reinforcing material for the manufacture of fiber reinforced plastics (FRP), and is also used for weaving high temperature resistant fiber cloth.But the glass fiber that has not been treated is brittle, easy to take static electricity after friction, and the surface is smooth, when making the reinforcing material of the resin is not easy to stick with the resin.In the m...
1.The cause of a back adhesion： (1)the paste itself anti-viscosity, especially in the wet weather easy to stick back; (2)After the printing is completed, it is packaged without perfect heat treatment; (3)adjust the slurry formula is not appropriate, adding too much transparent slurry easy to cause back adhesion; (4)transport or storage conditions are not good, in high temperature, high humidity co...
One, extinction principle General can be divided into physical extinction and chemical extinction.Physical matting, is the addition of matting agent, so that the coating in the film when the uneven surface, reduce reflection and achieve low gloss. Two, the kind of matting agent Coating common matting agent can be divided into organic matting agent and inorganic matting agent two categories. 1.Orga...
The choice of solvent In the printing ink manufacturing process, in consideration of the overall solvent system of the ink volatility, to improve the printing ink solvent release and reduce the solvent organic solvent residue, the use of solvents are often several volatile mixed solvents.In the printing ink manufacturing process, the main organic solvents are toluene, butanone, cyclohexanone, ethy...
sinograce chemical
Sinograce Chemical is professional technical enterprise providing solutions of surface materials and manufacturing of raw materials. Sinograce Chemical Company is composed of R&D center, Manufacture center, Quality control department, Market center and International trade department. We have been dedicating to research on excellent paint/coating, adhesive for over 15 years. And now still conti...
Room 1013, Building A5, Financial Port Center, Yangzijiang Road, Baohe District, Hefei City， Anhui province, China
+86 0551 63459511
Copyright © 2015-2025 Anhui Sinograce Chemical Co., Ltd..All Rights Reserved.powered by dyyseo.com
top
English
français
русский
español
العربية