Categories
new blog
The third step in the treatment of water-based paint coated substrates is sealing. The role of the water-based putty is to make the surface of the substrate such as wood not very regular and smooth and minor defects and defects, such as pores, fine cracks, pits, joints and concrete, to reduce the surface roughness and increase the flatness.The requirements for water-based putty are good adhesion a...
Paint of water-based paint - Waterborne wood paint application process 2 Before using the soft brush, thoroughly soak it in clean water, remove excess water, and do not drip. The enamel paint should only reach half the length of the bristles.Brush as fast as possible, gently and smoothly brush the wood grain, and do not apply it back and forth repeatedly. Because the water-based paint dries quickl...
Spraying construction paint film than brush paint film more flat. Spray with water-based wood paint should be added on the basis of the original paint 5% ~ 30% of the tap water dilute after use, for the viscosity of the paint water should also increase, the diluted paint after its coating a 4 cup viscosity should be around 18 ~ 20s. Dilute mix well should be static at least 20 minutes, until the b...
Waterborne paint testing and standards:hardness Hardness is one of the most important physical properties of a coating. Coating hardness reflects the coating's ability to resist constant dents, scratches, scribes, and penetrations caused by a hard object. Testing the hardness of materials with different methods will give different results because the testing methods are for different amounts of ma...
Current problems with waterborne polyurethane adhesives: (1) Low solid content: At present, the solid content of water-based polyurethane (WPU) can reach 45%. Fewer systems lead to higher drying and transportation costs. Increasing the solid content leads to an increase in the viscosity of the system, which makes emulsification and dispersion difficult. Reduced emulsion stability. (2) Slow drying ...
Precautions for using two-component polyurethane adhesives 1.Before applying the adhesive, the surface of the adherend must be clean, dry and free of grease. 2.The resin and curing agent should be mixed in the required ratio. 3.When scraping the glue, please try to scrape it carefully as it has a defoaming effect. 4.Store adhesive in (> 10, <50 * C) and dry place 5.Run out of the mixed glue ...
Glass fiber is an important reinforcing material for the manufacture of fiber reinforced plastics (FRP), and is also used for weaving high temperature resistant fiber cloth.But the glass fiber that has not been treated is brittle, easy to take static electricity after friction, and the surface is smooth, when making the reinforcing material of the resin is not easy to stick with the resin.In the m...
Environmentally friendly water-based polyurethane waterproof coating is two-component,The component A is an isocyanate-terminated prepolymer obtained by polycondensation of polyether and isocyanate, and the component B is a colored liquid composed of a plasticizer, a curing agent, a thickener, a coagulant, and a filler.After use, the two components of methyl and ethyl are evenly mixed according to...
Thank you for the New Year gift of our company. In the New Year, we hope to make our products better and serve our customers better,Hope the performance increase day! Sinograce Chemical wish you a happy New Year!
1.The cause of a back adhesion： (1)the paste itself anti-viscosity, especially in the wet weather easy to stick back; (2)After the printing is completed, it is packaged without perfect heat treatment; (3)adjust the slurry formula is not appropriate, adding too much transparent slurry easy to cause back adhesion; (4)transport or storage conditions are not good, in high temperature, high humidity co...
One, extinction principle General can be divided into physical extinction and chemical extinction.Physical matting, is the addition of matting agent, so that the coating in the film when the uneven surface, reduce reflection and achieve low gloss. Two, the kind of matting agent Coating common matting agent can be divided into organic matting agent and inorganic matting agent two categories. 1.Orga...
In polyurethane waterproof coating construction often encounter some problems, so in the process of waterproof construction encountered different problems how to solve it?sinograce waterproof with you to learn the following, polyurethane waterproof coating construction common problems and solutions. 1. viscosity (1) coating itself viscosity is very large, construction effort. (2) if the client app...
At present, two-component waterborne polyurethane has been widely used in leather, textile dyeing AIDS, adhesives, foam materials, coatings and other fields. With the continuous development of two-component waterborne polyurethane scientific research, it is gradually replacing solvent polyurethane as the medium to occupy the dominant position in the market. One: leather China's leather resources, ...
1.Introduction to silicone acrylic emulsion Silicon-acrylic emulsion is a kind of composite emulsion. It is a copolymer emulsion of organosilicone and acrylate.Acrylic resin has many excellent characteristics, such as weather resistance and light resistance, long time under ultraviolet irradiation is not easy to yellow。In addition, it also has flexibility, so it is often used as a leather finishin...
Anhui Sinograce Chemical Co., Ltd Polyurethane condoms, known as condoms, are made of polyurethane condoms, similar to latex condoms. Polyurethane was applied to condom production in Japan, until the emergence of China's Nakagawa 001, which broke Japan's monopoly on the production field. Because the common latex condoms on the market are thicker and polyurethane has good ...
Plasticizer is widely used in industrial production of polymer materials auxiliaries, also known as plasticizers. All substances added to polymer materials that increase polymer plasticity are called plasticizers. The use of plasticizer can improve the properties of polymer materials, reduce production costs and improve production efficiency. is a class of important chem...
sinograce chemical
Sinograce Chemical is professional technical enterprise providing solutions of surface materials and manufacturing of raw materials. Sinograce Chemical Company is composed of R&D center, Manufacture center, Quality control department, Market center and International trade department. We have been dedicating to research on excellent paint/coating, adhesive for over 15 years. And now still conti...
Room 1013, Building A5, Financial Port Center, Yangzijiang Road, Baohe District, Hefei City， Anhui province, China
+86 0551 63459511
Copyright © 2015-2025 Anhui Sinograce Chemical Co., Ltd..All Rights Reserved.powered by dyyseo.com
top
English
français
русский
español
العربية