Categories
new blog
1.Energy conservation: Water in water multicolor coating, pure water-based formula, excellent raw material technology.Granite stone, depending on nature, the development of powerful resources have some damage to the ecological. Water covered with colorful paint to solve this problem, and decorative curtain wall color can be artificially controlled, energy saving and environmental protection,commen...
Water-in-water multi-color paint spray guns to use most of the spray, for the operation, but also because of the improper use of the gun caused by uneven distribution of the coating,the following together to see how to solve it. The smaller the gun distance, the greater the pressure of the spray, the greater the impact of the product by the pressure of the water, water-in-watercolorful paint coati...
water-based resin | water-based industrial coating (a) water paint common problems Water based paint common problem: bubble - big bubble Large bubbles are large, visible bubbles that are visible to the naked eye. Bulk bubbles generally occur during the production or application of water-based paints. Possible solutions: 1. Use appropriate defoaming agents In the process of producing water-based pa...
water-based resin | water-based industrial coating (a) water paint common problems Common problems with water-based lacquer wood paint: transparency, Color fullness of shade The complaint that often hears about paint of ability in water is paint of ability in water diapure is poor, cannot show the plump godliness of woodiness. In general, the transparency of water-based paint is determined by the ...
Water - based wood paint common problems: gloss wood paint uneven luster Phenomenon There is light coating on the wood surface, coating film gloss, some areas of low gloss. Cause The wood fiber and pith ray in cork are loose with the growth of growth rings, the base material infiltrates excessively, the coating film increases the pigment volume concentration due to the decrease of the base ma...
How to solve the poor adhesion of water-based paint after soaking in water? Problems: water-based acrylic resin, self-drying system,60 ℃ / 120 minutes after the bubble row down into the water, can use fingernail.But after taking out to wait for water to be able again, how should solve? Response: This test method is still very harsh.General water - based resins, acrylic acid, polyurethane or Self-c...
Case study of water-based paint: the quality of water-based paint is unstable Maintaining the stability of waterborne coatings is one of the keys to the success of waterborne coatings manufacturers. This is especially important for manufacturers of industrial waterborne paints. There are many reasons for the unstable quality of water based paint, such as water-based paint process,water-based paint...
Ask the water-based paint expert -water-based glass paint appears prickly heat when baking Problem: I use water-based acrylic and amino resin to make the glass paint when baking prickly heat. The details are as follows: Temperature: 80 degrees Time: 2 minutes It was already smooth when it was put into the oven Flash dry for 10 minutes Has been changed to defoamer, leveling agent, solvent, no effec...
Leveling and rheological properties of waterborne coatings Problem: water borne white coating wants to have certain rheological already, want to maintain just right leveling sex again, how to do？ Response： This problem is one of the characteristics and technical characteristics of water based paint，In principle, it is mainly the relationship between equilibrium viscosity and rheology (plasticity)....
Wood bumps - Common problems with water paint Wood grain is exposed when broken or damaged wood comes into contact with water.A good example of this is when a curved toothpick is placed in water, it will draw water through the capillaries, elongate, and straighten.When the fibers on the board are exposed, they suck water into the wood like a straw, causing the fibers to swell and stick to the surf...
Problem：Some of the materials used in the construction of wood products are plywood and wood chip fiberboard. One of the rubber is the most afraid of water, water paint spray will dissolve the inside of the glue. The effect that USES close lacquer also is not ideal, how should solve? Is it easy to use sinograce chemical raw material solution? thank you . Response:This type of wood is usually ...
Common problems of water based paint: causes of shrinkage and solutions Shrinkage, known as cratering, is a common problem with water-based paints。The main cause of shrinkage cavity is impurities in water-based paint. In particular, there is oil in the area where the shrinkage cavity occurs, making the area unable to be wetted.In practical operation, the main causes of shrinkage cavity are as foll...
Question: Dear expert, I am now eager to develop a new water-based paint mainly for wood. The problem that needs to be solved urgently is the drying time of water-based paint. I want his dry time to be in 30 seconds, can you achieve excuse me, excuse me be colophony its key effect. Response: Hello, the dry time of water - based paint has two concepts commonly."Surface dryness" refers to the basic ...
Question: how to make water-borne heat-resistant paint and water-borne silver powder paint? Whose resin is better? Can you provide the reference formula? Response: Hello, Mr.Zheng,We have received many similar requests for reference formulations.Industrial coatings are characterized by their complexity.It is water borne anti-rust paint likewise,because use environment and the different that ask, f...
PH adjustment of water-based paint-Ask water character paint expert Question: If the pH value of the water-based paint is not weakly alkaline or the pH value is unstable, what effect will it have in actual use? Thank you! Response: The unstable pH of water-based paints has two main effects on water-based paints.One is that it affects the stability of the filler or paste in the resin because the pH...
Is the black spot on the surface of the water-based paint mildew? Problem: The wooden doors of our company's surface veneer have no black spots before they are painted. After spraying the water-based paint (primer + top coat), black spots appear on the veneer during the natural drying process. I wonder if the water-based paint is mildewed? If the oil-based colorant is used to seal the bottom, will...
sinograce chemical
Sinograce Chemical is professional technical enterprise providing solutions of surface materials and manufacturing of raw materials. Sinograce Chemical Company is composed of R&D center, Manufacture center, Quality control department, Market center and International trade department. We have been dedicating to research on excellent paint/coating, adhesive for over 15 years. And now still conti...
Room 1013, Building A5, Financial Port Center, Yangzijiang Road, Baohe District, Hefei City， Anhui province, China
+86 0551 63459511
Copyright © 2015-2025 Anhui Sinograce Chemical Co., Ltd..All Rights Reserved.powered by dyyseo.com
top
English
français
русский
español
العربية