Categories
new blog
Phenomenon : Part of the water-based paint film from the primer uplift, which contains gas or liquid, showed uneven distribution. Cause 1.When the water-based paint is applied, the dry water-based paint film is exposed to rain. 2.Apply a water-based paint primer to the wet substrate. 3.Water - based paint film is affected by acid - base and heat. Amelioration 1.Considering the gas phase conditions...
Phenomenon: Wood coating water - based varnish after the grain fuzzy, grain color and luster differ, failed to retain the original style of wood. cause 1.Transparent putty transparency is poor or scraping too thick, reduce the clarity of wood grain. 2.Water-based paint storage time is too long, pigment precipitation, on the shallow under the deep operation without mixing evenly, coating film thick...
Common problem of lacquer of waterborne woodwork: varnish besmear film is not level off, burnish is not even Phenomenon : Wood is filled with putty hole processing, after sealing the bottom, coating brush varnish, coating film flatness is low, luster is not uniform. Cause : Hole putty poor quality, loose, solvent absorption. The wood fiber and pith ray on the wood surface are relatively loose. The...
Water-based wood paint runs off oil---Ask a water paint expert Question: Waterborne wood lacquer should run oil to a rainy day only, or brush one day, also can run oil when waiting for the 2nd day to brush again, did especially ugly later . Water-based white paint does not have this problem. The problem ofwater-based varnish is obvious. Answer： Although it is a water-based paint, the film is hydro...
Basic knowledge of water-based paint In order to provide product development support to a wide range of waterborne coating formulation technicians and waterborne coatings sales personnel, we hav collected and summarized a large number of domestic and international market trends and technical points. Visit our waterborne coatings knowledge base and you can see all of our formulation techniques and ...
The film-forming aids for waterborne wood coatings are generally alcohol ether type solvents. The most commonly used filming aids such as diethanol ethers, propylene glycol ethers and N-methylpyrrolidone have high and low boiling points.Water-based wood coatings in the summer construction, the water volatilization is faster, that is, the surface is relatively fast, some of the moisture may be encl...
Defoamer is one of the most difficult additives in waterborne wood coatings to control the balance between defoaming and leveling.The paint liquid will generate bubbles during the application due to agitation .If the bubbles present in the paint are not removed in time, the film will dry and form an unacceptable flaw.The paint also produces air bubbles during production, pumping and filling. Defoa...
Waterborne paint formulation design system - pH regulator Waterborne wood coatings may also need to adjust the pH when necessary.Most emulsions or aqueous dispersions have been adjusted to a pH of 8 to 9 when they are produced, eliminating the need for pH adjusters when making paint.If the pH value is different, add 0.05% to 0.1% of the pH adjuster during the paint making process, and adjust the p...
1.The tool Before using the soft brush, thoroughly soak it in clean water, remove excess water, and do not drip. The enamel paint should only reach half the length of the bristles.Brush as fast as possible, gently and smoothly brush the wood grain, do not apply it back and forth repeatedly, because the water-based paint is fast drying and the opening time is short, so it should be completed as soo...
3.Process variations of different paint types-Waterborne wood paint application process 2 Applying a matt lacquer to the varnish can change the coating to a matte finish, while applying a varnish to a matt lacquer reduces the brightness of the film and does not achieve maximum brightness and transparency. The color paint of waterborne wood lacquer can be divided into two types: coloured coating an...
Water-based wood lacquer can be used to apply. The characteristics of the brush method is simple, easy to master, fast coating speed, and can eliminate the brush method commonly seen bubbles and brush marks and other shortcomings. This is because the paint left on the surface of the wood is very thin and the pressure of the brush is high, which makes the air in the wood grain and micro hole easy t...
Water based wood lacquer is mainly made of waterborne acrylic acid and polyurethane and refined by strict production process standards. It is suitable for the protection of indoor wood and wood products, and can play the role of decoration, protection and service life extension.Waterborne wood lacquer uses water as diluent, does not contain benzene and other harmful substances, non-toxic...
Pigment is a white or colored fine powder substance which is generally insoluble in water, oil and solvents (some pigments are soluble), but can be evenly dispersed in water.Pigment and film forming material solution mixed on the surface of the material, can form a covering ability of various colors of the paint layer in wood products coating or finishing process, pigment has three functions. It i...
1
adminpages
sinograce chemical
Sinograce Chemical is professional technical enterprise providing solutions of surface materials and manufacturing of raw materials. Sinograce Chemical Company is composed of R&D center, Manufacture center, Quality control department, Market center and International trade department. We have been dedicating to research on excellent paint/coating, adhesive for over 15 years. And now still conti...
Room 1013, Building A5, Financial Port Center, Yangzijiang Road, Baohe District, Hefei City， Anhui province, China
+86 0551 63459511
Copyright © 2015-2025 Anhui Sinograce Chemical Co., Ltd..All Rights Reserved.powered by dyyseo.com
top
English
français
русский
español
العربية