Categories
new blog
Waterborne paint testing and standards:hardness Hardness is one of the most important physical properties of a coating. Coating hardness reflects the coating's ability to resist constant dents, scratches, scribes, and penetrations caused by a hard object. Testing the hardness of materials with different methods will give different results because the testing methods are for different amounts of ma...
Current problems with waterborne polyurethane adhesives: (1) Low solid content: At present, the solid content of water-based polyurethane (WPU) can reach 45%. Fewer systems lead to higher drying and transportation costs. Increasing the solid content leads to an increase in the viscosity of the system, which makes emulsification and dispersion difficult. Reduced emulsion stability. (2) Slow drying ...
Precautions for using two-component polyurethane adhesives 1.Before applying the adhesive, the surface of the adherend must be clean, dry and free of grease. 2.The resin and curing agent should be mixed in the required ratio. 3.When scraping the glue, please try to scrape it carefully as it has a defoaming effect. 4.Store adhesive in (> 10, <50 * C) and dry place 5.Run out of the mixed glue ...
1.The cause of a back adhesion： (1)the paste itself anti-viscosity, especially in the wet weather easy to stick back; (2)After the printing is completed, it is packaged without perfect heat treatment; (3)adjust the slurry formula is not appropriate, adding too much transparent slurry easy to cause back adhesion; (4)transport or storage conditions are not good, in high temperature, high humidity co...
The choice of solvent In the printing ink manufacturing process, in consideration of the overall solvent system of the ink volatility, to improve the printing ink solvent release and reduce the solvent organic solvent residue, the use of solvents are often several volatile mixed solvents.In the printing ink manufacturing process, the main organic solvents are toluene, butanone, cyclohexanone, ethy...
Water-based wood lacquer can be used to apply. The characteristics of the brush method is simple, easy to master, fast coating speed, and can eliminate the brush method commonly seen bubbles and brush marks and other shortcomings. This is because the paint left on the surface of the wood is very thin and the pressure of the brush is high, which makes the air in the wood grain and micro hole easy t...
Composition of water bases adhesive 1.adhesive: also known as adhesive agent, after the surface treatment of two or more adhesive materials firmly connected together, and has a certain mechanical strength of chemical properties, such as epoxy resin phosphate copper oxide white latex. 2.Solid material (base material): determines the main physical, chemical and mechanical properties of rubber joints...
1.Principles of adhesive selection Consider the type, nature and hardness of the bonding material Consider the shape, structure and process conditions of the bonding material Consider the load and form (tensile force, shear force, peel force, etc.) borne by the bonding part; consider the special requirements of materials such as high temperature and low temperature resistance. 2.Properties of bond...
Automotive interior adhesive is a anionic waterborne polyurethane emulsion developed and produced by ourselves, which belongs to environmental protection waterborne polyurethane adhesive. Appearance Dark grey liquid Solid content(% ) 50±1 PH 6-9 softening point(℃) 45-55℃ Proportion（g/cm3） 1.06±0.02 viscosity（mPa.s） 1000-2000（Viscosity can be adjusted） Application Area Automobile interior adhesive ...
Water based wood lacquer is mainly made of waterborne acrylic acid and polyurethane and refined by strict production process standards. It is suitable for the protection of indoor wood and wood products, and can play the role of decoration, protection and service life extension.Waterborne wood lacquer uses water as diluent, does not contain benzene and other harmful substances, non-toxic...
Laminated oil magnetic cards, Identification Card and other cards used in water-based adhesive. The card is both a document and a form or carrier of the document's existence, although it has entered the 5G era,Many things exist in electronic form, such as electronic balance cards, electronic driver's licenses, electronic health care cards, etc.But the physical card such as id card bank card is als...
Printing mucilage requirements The requirements of printing mucilage for manual plate printing Manual table printing is to press the screen on the fabric of the table for manual scraping, and the pressure extrusion on the scraper will print the glue through the mesh hole of the pattern part to the fabric. The shear stress of the binder is small, so thePrinting mucilageis required to have good...
Food packaging is divided into ordinary packaging and high-performance packaging, the corresponding waterborne polyurethane adhesive can be divided into four categories: general use, steaming boiling, transparent cooking, aluminum foil cooking.Usually such adhesives are two-component solvent-based polyurethane adhesives, the main agent is polyether or polyester polyol After the aromatic isocyanate...
When waterborne polyurethane is used as adhesive, it must be mixed generally. Based on waterborne polyurethane, crosslinking agent, thickening agent, filler, plasticizer, pigment and other additives can be added. Other types of waterborne resin and water can be added.In order to obtain higher resistance to water Heat resistance and bonding strength, at present a lot of waterborne polyurethane syst...
Water - based ink is composed of adhesives pigment additives and other substances such as uniform slurry material,Binders provide ink with the necessary transfer properties, pigments give ink color. Water-based ink linker is mainly divided into two types: water dilution and water dispersion.The former can be used in many types of resin, such as maleic acid resin lac maleic acid resin modified shel...
Waterborne polyurethane adhesive is a kind of high-grade adhesive, with excellent flexibility, impact resistance, chemical resistance and wear resistance, the most important is its low temperature resistance.It has adsorption and chemical bonding effect on many kinds of materials. It can not only bond porous materials, but also bond smooth surface materials. It is widely used. Polyurethane adhesiv...
sinograce chemical
Sinograce Chemical is professional technical enterprise providing solutions of surface materials and manufacturing of raw materials. Sinograce Chemical Company is composed of R&D center, Manufacture center, Quality control department, Market center and International trade department. We have been dedicating to research on excellent paint/coating, adhesive for over 15 years. And now still conti...
Room 1013, Building A5, Financial Port Center, Yangzijiang Road, Baohe District, Hefei City， Anhui province, China
+86 0551 63459511
Copyright © 2015-2025 Anhui Sinograce Chemical Co., Ltd..All Rights Reserved.powered by dyyseo.com
top
English
français
русский
español
العربية