• Characteristics of plastic substrate and its effect on coatings
    • 2020-02-21 14:49:01
    • admin

    Plastics are classified into two types: thermosetting and thermoplastic.Among them, thermosetting plastics have high cross-linking density, good solvent resistance and heat resistance, relatively high surface polarity, and wide range of coatings available.For example, unsaturated polyester is called polyester fiberglass. The texture is hard and polar, and there are many coatings that can be used. ...

  • Steel use environment and corrosion conditions
    • 2020-02-21 15:00:04
    • admin

    The steel is subjected to different degrees of corrosion conditions in different operating environments. According to the corrosion conditions, the environmental conditions used by the steel are divided into four grades: Steel use environment and corrosion conditions Steel use environment and corrosion conditions Definition Performance Requirements Coating Effect Harsh conditions Products used in ...

  • Wood coating process
    • 2020-02-21 15:31:03
    • admin

    Wood coating process 1.There are many large holes in the hard wood, putty or hole adding agent to flatten; 2.Apply closing primer after hole filling; 3.If you need to deepen the surface texture of the wood and highlight the wood grain, you can apply the closed primer and apply the water color; 4.After conditioning the wood grain, apply two closed primer; 5.Finish with top coat. Sinograce Chemical ...

  • Effect of wood substrate on coatings
    • 2020-02-21 16:19:26
    • admin

    Due to the chemical composition of the wood and the particularity of the wood fiber, if it is not handled properly, the water-based paint film will be damaged. Wood is composed of cellulose and a small amount of gum, resin (rosin), pigment, tannin and the like. Although the amount of gum, resin, pigment, tannin, etc. is small, it has a large negative impact on the properties of the coating (mainly...

  • Characteristics of wood matrix and its effect on coatings
    • 2020-02-21 15:43:18
    • admin

    To master waterborne wood coatings and coatings, you must be familiar with the characteristics of wood. In this way, we can find the root cause of the problem in the painting process and make the necessary preventive and treatment measures. Wood is a natural fiber material, seen from the cross section of the trunk, it is a uniform material composed of layers of different materials, with many textu...

  • Formulation design system for waterborne coatings - other additives
    • 2020-02-21 16:24:30
    • admin

    Essence As long as the amount of essence can improve the odor of the paint liquid, the dosage is about 0.05%, and the individual case can be as high as 0.1%. Of course, it can be used. ultraviolet light absorber Indoor water-based wood paint rarely use ultraviolet absorbent, for the use of TDI emulsion or moisture dispersion production of varnish and outdoor paint, especially outdoor white paint h...

  • Formulation design system for waterborne coatings - pigments and fillers
    • 2020-02-21 16:23:29
    • admin

    In the solid paint, white paint is taken as an example. The amount of titanium dioxide should be sufficient to ensure that the paint film has sufficient capping power. The amount of titanium dioxide should not be lower than 13%, but it is not necessary to be higher than 22%. The situation is the same as solvent-based white paint. Fillers may be added or not added. However, a small amount of filler...

  • Waterborne paint formulation design system - pH regulator
    • 2020-02-21 16:35:41
    • admin

    Waterborne paint formulation design system - pH regulator Waterborne wood coatings may also need to adjust the pH when necessary.Most emulsions or aqueous dispersions have been adjusted to a pH of 8 to 9 when they are produced, eliminating the need for pH adjusters when making paint.If the pH value is different, add 0.05% to 0.1% of the pH adjuster during the paint making process, and adjust the p...

  • Water-based coating formulation design system - preservative
    • 2020-02-21 16:42:59
    • admin

    Water-based coating formulation design system - preservative Water-based wood coatings are water-based systems that are easier to bring into bacteria during production and are more susceptible to microbial degradation during storage. Therefore, the type and amount of preservatives should be properly added during formulation to prevent system and coating corruption.From the perspective of environme...

Copyright © 2015-2024 Anhui Sinograce Chemical Co., Ltd..All Rights Reserved.powered by dyyseo.com

top