Categories
new blog
Common problem of lacquer of waterborne woodwork: varnish besmear film is not level off, burnish is not even Phenomenon : Wood is filled with putty hole processing, after sealing the bottom, coating brush varnish, coating film flatness is low, luster is not uniform. Cause : Hole putty poor quality, loose, solvent absorption. The wood fiber and pith ray on the wood surface are relatively loose. The...
Water-based wood paint runs off oil---Ask a water paint expert Question: Waterborne wood lacquer should run oil to a rainy day only, or brush one day, also can run oil when waiting for the 2nd day to brush again, did especially ugly later . Water-based white paint does not have this problem. The problem ofwater-based varnish is obvious. Answer： Although it is a water-based paint, the film is hydro...
Oil pocket phenomenon in water-based paint Problem: To make furniture with transparent colors, in order to save the craft and achieve the purpose of simple construction. We added water-based Color Concentrate to the topcoat for spraying, and the resulting topcoat contained some oil pockets or other unacceptable "face problems." Reply: Aqueous color concentrates are generally made of metal complexe...
To master waterborne wood coatings and coatings, you must be familiar with the characteristics of wood. In this way, we can find the root cause of the problem in the painting process and make the necessary preventive and treatment measures. Wood is a natural fiber material, seen from the cross section of the trunk, it is a uniform material composed of layers of different materials, with many textu...
Cohesion and thermal expansion coefficient of paint film The force caused by the cohesion of molecules of the same substance is called cohesion.The more cohesive the coating, the worse the adhesion.In the drying process of paint, with the increase of solvent volatilization and crosslinking degree, the cohesion between film forming material molecules increases, the film produces shrinkage phenomeno...
The adhesion of the paint film is caused by the mutual attraction between the paint and the polar groups on the surface of the coated substrate, and the mutual attraction between the polar groups is based on the premise that the paint is well wetted on the surface of the coated substrate.Since the wet condition of the coating on the surface of the coated substrate depends on the surface tension of...
The third step in the treatment of water-based paint coated substrates is sealing. The role of the water-based putty is to make the surface of the substrate such as wood not very regular and smooth and minor defects and defects, such as pores, fine cracks, pits, joints and concrete, to reduce the surface roughness and increase the flatness.The requirements for water-based putty are good adhesion a...
3.Process variations of different paint types-Waterborne wood paint application process 2 Applying a matt lacquer to the varnish can change the coating to a matte finish, while applying a varnish to a matt lacquer reduces the brightness of the film and does not achieve maximum brightness and transparency. The color paint of waterborne wood lacquer can be divided into two types: coloured coating an...
Spraying construction paint film than brush paint film more flat. Spray with water-based wood paint should be added on the basis of the original paint 5% ~ 30% of the tap water dilute after use, for the viscosity of the paint water should also increase, the diluted paint after its coating a 4 cup viscosity should be around 18 ~ 20s. Dilute mix well should be static at least 20 minutes, until the b...
1.Paper-based coating resins have been switched from natural water-based resins such as celluloses to synthetic resin emulsions such as carboxystyrene butadiene emulsions, polyvinyl acetate emulsions, and acrylic emulsions, among which acrylic emulsions have more excellent properties.However, the above resins are still difficult to meet the higher requirements for the development of coated paper. ...
First, pour the glue on the flat glass to observe its rheology, and wiggle it to observe its rheology,If the flow of glue is too fast, it means that the glue is too thin and poor, and too thick is not conducive to bonding. Secondly, with a hand dip to observe its viscosity if you can slowly draw, a little sticky hand is better. Then, pour it on a small piece of glass to observe its film forming ti...
Sixteen common types of self-adhesive labels This paper introduces sixteen types of self-adhesive labels commonly seen in daily life. The specific types of self-adhesive labels are as follows： 1. Press smooth writing paper and offset paper labels Multi-purpose label paper for information labels, bar code printing labels, especially suitable for high speed laser printing, also suitable fo...
Eight, filling The concept of filling is rarely mentioned in the application of laminating glue, but can never be ignored.The surface of the paper inevitably exists in some depression. When compounding, if the depression in the paper cannot be fully filled, it will also cause the weak. (Excellent filling effect) &nb...
Labels, as they are called in the printing industry, are mostly printed materials used to identify the relevant instructions of their products, and most of them come with glue on the back. But there are also some printing without glue, can also be called labels. Glue label is colloquially known as "sticker label". Label base material classification Substrate application surface material paper...
Self-adhesive refers to paper, film or other special materials as fabric, coated with adhesive on the back, a composite material printed with silicon protective paper as the base paper, the reason for the rapid rise of self-adhesive in recent years, because it is very practical, and very convenient, the cost is not high, the following to tell you about a few small knowledge of self-adhesive printi...
Water based adhesive for a more sustainable bond The market share of water-based adhesives is becoming increasingly large as development has shifted towards increasingly sustainable solutions that support health and safety and reduce environmental impact.Water-based adhesives are an excellent alternative to solvent-based systems because they do not contain any volatile organic compounds (VOC), are...
1
3
adminpages
sinograce chemical
Sinograce Chemical is professional technical enterprise providing solutions of surface materials and manufacturing of raw materials. Sinograce Chemical Company is composed of R&D center, Manufacture center, Quality control department, Market center and International trade department. We have been dedicating to research on excellent paint/coating, adhesive for over 15 years. And now still conti...
Room 1013, Building A5, Financial Port Center, Yangzijiang Road, Baohe District, Hefei City， Anhui province, China
+86 0551 63459511
Copyright © 2015-2025 Anhui Sinograce Chemical Co., Ltd..All Rights Reserved.powered by dyyseo.com
top
English
français
русский
español
العربية