non-stick marble coating for marble coating non-stick pan is Water based Two-layer Marble-Coating (Starry Sky). It is widely applied to internal coating of non-stick kitchenware such as aluminum-made frying pans, woks, stockpots, electric stewpots, electric bake wares and cake molds.
Brand:
sinograceitem no.:
PF-612Payment:
L/C、D/A、D/P、T/T、MoneyGram、Paypal Otherproduct origin:
China Anhuishipping port:
Shanghai And Other PortsLead Time:
15-25 DaysDescription
non-stick marble coating for marble coating non-stick pan is Water based Two-layer Marble-Coating (Starry Sky). It is widely applied to internal coating of non-stick kitchenware such as aluminum-made frying pans, woks, stockpots, electric stewpots, electric bake wares and cake molds.
Type
Water based marble-coating
non-stick marble coating for marble coating non-stick pan
Key features
-Eco-friendly and PFOA free
-Showing the effect of natural marble
-Excellent chemical resistance and abrasive resistance
-Excellent and lasting non-stick performance, easy to clean
Typical properties
Product model: PF-612P (Primer)
PF-612T (Top)
PF-612D1 (Dot 1)
PF-612D2 (Dot 2)
Recommended dosage: 10kg Primer: 10kg Top
0.5kg Dot 1: 0.5kg Dot 2
Appearance: Black (Primer)
Black (Top)
White (Dot 1)
Light yellow (Dot 2)
Solid content (%): 35±1 (Primer)
45±1 (Top)
40±1 (Dot 1)
39±1 (Dot 2)
Viscosity (cp): 600~1000 (Primer)
300~800 (Top)
300~800 (Dot 1)
300~800 (Dot 2)
Density (g/ml): 1.20±0.20 (Primer)
1.30±0.20 (Top)
1.25±0.20 (Dot 1)
1.25±0.20 (Dot 2)
pH: 8~11 (Primer)
8~11 (Top)
8~11 (Dot 1)
8~11
Gloss (60° glossimeter): 10-20
Film thickness (μm): 35-45
Non-stick performance: >10 cycles (Fry eggs at 160±10℃)
Corrosion resistance: No blister (Boling 10% salt water (24 hours))
Abrasion resistance 3KG/21cm2: >5000 cycles
Hardness: 2H (ZHONGHUA pencil)
Adhesion (1mm*1mm): Grade 1
non-stick marble coating for marble coating non-stick pan
Application
-Inside of tensile aluminum and die-casting fry pan, wok, soup pot, etc.
Storage and handling
-Available in 20 kg/ barrel or 30 kg/ barrel
-Store products in tightly closed original containers at 5-35℃
-Shelf life: 6-9 months from delivery date
-According to non-dangerous goods transport
How to use
1. Requirement on pre-treatment
-Firstly, apply high-temperature degreasing, then wash with 1%~3% NaOH solution (60℃) for more than 6 minutes, dry it after water rinsing.
-Blast with 80#~120# corundum to make the surface roughness reach 2.0μ~3.0μ, pay attention to sandblast evenly;
-Wash with 1%~3% NaOH solution(60℃) for more than 6 minutes, rinse with water.
-Wash with 1%~3% hydrochloric acid solution (60℃) for more than 6 minutes, rinse with water and dry.
2. Preparation of the coating
-Dispersion of coating: the coating must be fully dispersed before operation. Rolling the coating at the speed of 30rpm with rolling machine for 30mins, shouldn’t exceed 60 mins.
-Viscosity adjustment: the viscosity could be adjusted according to different spray methods. Dilute with clean water if the viscosity is over high.
-Coating filtration: filtrate the coating with screen (100mesh) before using.
3. Application
-The spraying environment should be dry, well-ventilated, no smoking and fire. We suggest using dedicated spray gun, elevated tank and curing oven.
-The air compressor should be degreased, dewatered and equipped with water oil separator before using.
-Adjust atomization and oil pump capacity of the spraying gun; make sure the unit is clean and flat.
-Preheat the substrate to 35℃ and spray the primer. Dry it at temperature of 120℃~180℃ for 10min-15min. Keep the thickness of primer within 15μm-20μm.
-Spray top coating after the primer is dry and cooling to room temperature, then spray the dot. Dry the unit at the temperature of 150℃~200℃ for 10min~20min, and gradually increase the temperature to 400℃~410℃(the temperature of substrates), keep for 10 min~15 min. Keep the thickness of top coat within 8μm~12μm. The total thickness of final coating film should be between 35μm~45μm.
-In spraying process, keep stirring inside of the elevated tank, the size of spraying nozzle should be between 1.3mm ~ 1.5mm, the pressure is about 2.5-4 bar.
-The oven (or the tunnel drier) must be well ventilated; otherwise, it will lead to color changing of coating.
Non-stick Coating Type
↓ ↓ ↓ Please click product model for more informations
Model | Layer | Thickness | Curing temperature | Non stick property | Anti-corrosion | Abrasion resistant |
Water based fluororesin non-stick coating | ||||||
PF-600 | 2 | 25-40 | 380-400 | A A A A A | A A A A | A A A |
PF-601 | 2 | 25-35 | 380-400 | A A A A | A A A A | A A A |
PF-602 | 2 | 25-40 | 380-400 | A A A A A | A A A A | A A A |
PF-610 | 3 | 20-35 | 380-420 | A A A A A | A A A A A | A A A |
PF-611 | 3 | 20-35 | 380-420 | A A A A A | A A A A A | A A A |
PF-612 | 3 | 20-35 | 380-420 | A A A A A | A A A A A | A A A |
Water based ceramic non-stick coating | ||||||
C-104 | 1 | 30-45 | 280-300 | A A A A A | A A A A | A A A A A |
C-105 | 1 | 30-45 | 280-300 | A A A A A | A A A A | A A A A A |
C-106 | 2 | 34-50 | 280-300 | A A A A A | A A A A | A A A A A |
C-107 | 1 | 12-20 | 250-280 | A A A A A | A A A A | A A A A A |
C-108 | 2 | 34-50 | 280-300 | A A A A A | A A A A | A A A A A |
C-109 | 2 | 34-50 | 280-300 | A A A A A | A A A A | A A A A A |
Silicone resin non-stick coating | ||||||
S-200 | 1 | 15-20 | 280-300 | A A A A | A A A A A | A A A A |
S-201 | 1 | 15-20 | 280-300 | A A A A | A A A A A | A A A A A |
S-202 | 1 | 15-20 | 280-300 | A A A A | A A A A A |
A A A A |
Previous:
marble granite non stick coating for cast frying pan with non-stick coating marble (Starry Sky) PF-612Next:
silicone nonstick coatings for aluminum non-stick cookwareCopyright © 2015-2024 Anhui Sinograce Chemical Co., Ltd..All Rights Reserved.powered by dyyseo.com
top