Categories
new blog
Defoamer is one of the most difficult additives in waterborne wood coatings to control the balance between defoaming and leveling.The paint liquid will generate bubbles during the application due to agitation .If the bubbles present in the paint are not removed in time, the film will dry and form an unacceptable flaw.The paint also produces air bubbles during production, pumping and filling. Defoa...
Water-based coating formulation design system - preservative Water-based wood coatings are water-based systems that are easier to bring into bacteria during production and are more susceptible to microbial degradation during storage. Therefore, the type and amount of preservatives should be properly added during formulation to prevent system and coating corruption.From the perspective of environme...
Waterborne paint formulation design system - pH regulator Waterborne wood coatings may also need to adjust the pH when necessary.Most emulsions or aqueous dispersions have been adjusted to a pH of 8 to 9 when they are produced, eliminating the need for pH adjusters when making paint.If the pH value is different, add 0.05% to 0.1% of the pH adjuster during the paint making process, and adjust the p...
To master waterborne wood coatings and coatings, you must be familiar with the characteristics of wood. In this way, we can find the root cause of the problem in the painting process and make the necessary preventive and treatment measures. Wood is a natural fiber material, seen from the cross section of the trunk, it is a uniform material composed of layers of different materials, with many textu...
Due to the chemical composition of the wood and the particularity of the wood fiber, if it is not handled properly, the water-based paint film will be damaged. Wood is composed of cellulose and a small amount of gum, resin (rosin), pigment, tannin and the like. Although the amount of gum, resin, pigment, tannin, etc. is small, it has a large negative impact on the properties of the coating (mainly...
As the saying goes, three-point paint, seven-point painting. For water-based coatings, especially for water-based wood coating in the home improvement market, the level of coating technology has a direct impact on product use. In order to let everyone better master the water-based paint technology, we specially launched the water-based paint coating process series this week. The substrate treatmen...
The third step in the treatment of water-based paint coated substrates is sealing. The role of the water-based putty is to make the surface of the substrate such as wood not very regular and smooth and minor defects and defects, such as pores, fine cracks, pits, joints and concrete, to reduce the surface roughness and increase the flatness.The requirements for water-based putty are good adhesion a...
1.The tool Before using the soft brush, thoroughly soak it in clean water, remove excess water, and do not drip. The enamel paint should only reach half the length of the bristles.Brush as fast as possible, gently and smoothly brush the wood grain, do not apply it back and forth repeatedly, because the water-based paint is fast drying and the opening time is short, so it should be completed as soo...
3.Process variations of different paint types-Waterborne wood paint application process 2 Applying a matt lacquer to the varnish can change the coating to a matte finish, while applying a varnish to a matt lacquer reduces the brightness of the film and does not achieve maximum brightness and transparency. The color paint of waterborne wood lacquer can be divided into two types: coloured coating an...
Spraying construction paint film than brush paint film more flat. Spray with water-based wood paint should be added on the basis of the original paint 5% ~ 30% of the tap water dilute after use, for the viscosity of the paint water should also increase, the diluted paint after its coating a 4 cup viscosity should be around 18 ~ 20s. Dilute mix well should be static at least 20 minutes, until the b...
Waterborne paint testing and standards:hardness Hardness is one of the most important physical properties of a coating. Coating hardness reflects the coating's ability to resist constant dents, scratches, scribes, and penetrations caused by a hard object. Testing the hardness of materials with different methods will give different results because the testing methods are for different amounts of ma...
Current problems with waterborne polyurethane adhesives: (1) Low solid content: At present, the solid content of water-based polyurethane (WPU) can reach 45%. Fewer systems lead to higher drying and transportation costs. Increasing the solid content leads to an increase in the viscosity of the system, which makes emulsification and dispersion difficult. Reduced emulsion stability. (2) Slow drying ...
At present, two-component waterborne polyurethane has been widely used in leather, textile dyeing AIDS, adhesives, foam materials, coatings and other fields. With the continuous development of two-component waterborne polyurethane scientific research, it is gradually replacing solvent polyurethane as the medium to occupy the dominant position in the market. One: leather China's leather resources, ...
Anhui Sinograce Chemical Co., Ltd Polyurethane condoms, known as condoms, are made of polyurethane condoms, similar to latex condoms. Polyurethane was applied to condom production in Japan, until the emergence of China's Nakagawa 001, which broke Japan's monopoly on the production field. Because the common latex condoms on the market are thicker and polyurethane has good ...
Plasticizer is widely used in industrial production of polymer materials auxiliaries, also known as plasticizers. All substances added to polymer materials that increase polymer plasticity are called plasticizers. The use of plasticizer can improve the properties of polymer materials, reduce production costs and improve production efficiency. is a class of important chem...
Water-based wood lacquer can be used to apply. The characteristics of the brush method is simple, easy to master, fast coating speed, and can eliminate the brush method commonly seen bubbles and brush marks and other shortcomings. This is because the paint left on the surface of the wood is very thin and the pressure of the brush is high, which makes the air in the wood grain and micro hole easy t...
sinograce chemical
Sinograce Chemical is professional technical enterprise providing solutions of surface materials and manufacturing of raw materials. Sinograce Chemical Company is composed of R&D center, Manufacture center, Quality control department, Market center and International trade department. We have been dedicating to research on excellent paint/coating, adhesive for over 15 years. And now still conti...
Room 1013, Building A5, Financial Port Center, Yangzijiang Road, Baohe District, Hefei City， Anhui province, China
+86 0551 63459511
Copyright © 2015-2025 Anhui Sinograce Chemical Co., Ltd..All Rights Reserved.powered by dyyseo.com
top
English
français
русский
español
العربية